Showing posts with label Chassis. Show all posts
Showing posts with label Chassis. Show all posts

Friday, 22 February 2008

Time Flys By...

Doesn't it just? Where are all the posts then?

My excuse? Well we did have a weeks holiday in Wales, and the usual preparation beforehand and sorting out on return meant I lost about a fortnight of modelling in all. But we had a ride on the Festiniog and bought an Ivor the Engine book, so not all was lost! This in turn prompted me to buy the Ivor DVD on return from said holiday and that in its own turn prompted me to buy the Trumptonshire DVD box set. So thats probably where the modelling time went. As they say, "Time Flys By..."




Back to the workbench and I need to get this D49 thingy cracked and then bang on with the layout. Through Edward, I am looking to get Alan Smith to make a "baseboard kit" for Brafferton to give a professional job. If I do it all myself, it's going to be rather rougharse; woodwork was never a strong point for me. Whilst I wait on that, better progess the D49 hadn't we?




Next job on the list was to insert the worm and complete the drive train. This was relatively straightforward; I'd done worms and stuff before. However the kit includes etches to manufacture the universal joints; a new idea to me. So these needed building up.






No, these aren't to deter 2mm vampires. They're the two halves of the ball part of the joint which are each made up of three layers of etch. The two halves are then soldered around some spring steel wire and the whole slots into the slotted tubes on the drive shafts.





What is not overly clear in the instructions is that these etches need a fair bit of meat taking off once assembled to enable them to work in the joint. Once one end had been done, I tacked half of the second assembly to the other end and check for length before fully soldering all parts together. My guestimate was quite good and I didn't need to shorten or lengthen the assembly after the trial run.





Once fully soldered, I gave the lot a right good clean and a dab of oil before checking the finished assembly for fit...





A quick wobble up and down the test track (no weight yet!) proved success. Now onto the loco body. I've done a bit this afternoon, and I'll try and post an update tonight or tomorrow. I'd hoped to get to Glasgow this weekend to see Mick and co at Model Rail Scotland. This is now looking unlikely due to work and family commitments. Shucks...


Friday, 1 February 2008

Don't tell him, Pike!

Stupid boy!

Yesterday I wrote "no mistakes" at which point Uncle Bob e-mailed me and pointed out the glaring error. The bearings for the pony truck go through the link, but ARE NOT SOLDERED so that when you tighten the retaining screw, you have a pivot. What a bufoon I am! Thank you Bob. Bearings have now been removed, the link cleaned of solder and new bearings merely PLACED in the holes.

On a brighter note, I've tweaked the brake assembly and this now sits in place without fouling any moving bits. Whether I get any farther tonight or tomorrow morning I don't know.

If you're coming to Bournmoor tomorrow afternoon, you can see it in the flesh (no, the D49 I mean!).

See you there

Wednesday, 30 January 2008

Saddle up the Palamino

More progress today:

i. Pony Truck. As per instructions. Straightforward, no mistakes (as yet discovered!)




ii. Brakes. Again fairly straightforward; fold up and solder with 0.3mm wires.




iii. Pony Truck on Chassis.




iv. Brakes have been on chassis, but I'm getting binding somewhere. A job for tonight or tomorrow night, perhaps!

Tuesday, 29 January 2008

Under Cover

Are you ever doing some modelling and you get to the point where you think, "Ooh, I never thought about that!"? Well I had just such a revelation at the start of the week.

The D49 chassis is up and running very nicely and all the motion is in place. It's at this stage that I notice the piston rods protruding from the front of the cylinder blocks. "When should they have come off?" I think. "It's going to be a bugger shortening them in situ!" Indeed it is...

I can't find any reference in the instructions as to when I should have shortened them and this makes me feel a little better. Ideally I would have done it before securing the crossheads and slidebars. As it is, I now have to cut them flush with the face of the cylinder without marking the said face too much. Tricky...


The piercing saw proves ideal, but work is slow and careful. Fortunately the piston covers will mask any markings on the cylinder front and the same cover is also half etched where the piston protrudes, so it doesn't have to be dead flush.


Meanwhile the bogie has been assembled and I hope to fit the wheels later tonight or tomorrow. Onward, ever onward...

On a green note, I replaced the bulb in my modelling anglepose lamp with one of these newfangled low energy ones. At 11W it obviously uses lots less electricity, but also the light seems somehow "cleaner" than a 60W standard bulb; I am finding it a lot easier to distinguish fine detail on my work. Additionally the heat thrown off is substantially less; certainly useful once we get into spring/summer.

Saturday, 26 January 2008

... Loco Motion

Motion: Part the Second.

On the right hand side of the D49/2 is the valve-gear; slightly different in that it has Lentz rotary poppet valves. A crank on the foremost driver rotates bevelled gears which drive through a shaft into the cylinder. Further gears and shafts operate the valves in the two cylinders.

Whilst relatively straightforward, the model set-up involves the mock gearbox "floating" on an etched arm and the drive shaft. The bracket, which in real life is attached to the footplate, serves no use in the model and the lining up of the components requires a fair degree of care.

There are no joints to manufacture on this side other than to solder the crank onto the crank-pin capturing the coupling and connecting rods and ensuring that the other end of the crank corresponds to the centre of the wheel. This was done by eye and I think is reasonably successful. If there is any slight misalignment, it is not obvious especially behind the gearbox.



The gearbox is manufactured from a fold up etch onto which we solder a small tube, to take the shaft, and a piece of 0.3mm wire to attach the arm that holds it. This seemed to be going swimmingly until I came to attach the whole to the chassis. On trimming the wires, I loosened the shaft tube; obviously the soldered joint was poor! Reattaching it, now that the gearbox was in-situ and the wires had all been trimmed, proved to be somewhat testing. Eventually I was happy that all was secure and in the correct place. Files and abrasives cleaned up the assembly before the whole chassis was given a thorough wash in the bathroom basin.



I consider the last few days work a success; despite all the gubbins which now adorns the chassis, it still runs very freely - better than I could have hoped for. I have learned some new techniques and pushed back my own modelling boundary a little further. Truth be told, despite the setbacks the motion has actually gone together much less painfully than I thought it would; I guess I can still surprise myself.



Now onto the bogie/pony (?) and then lets get some power to those wheels!

Friday, 25 January 2008

C'mon Baby, Do The...

Little discernable progress with the D49 over the last few weeks as the Layout Challenge kicks off. However I have been redoing the wheels; I was concerned that they were not sufficiently central when looking at the chassis face on. This became more apparent as I proceeded with the loco-motion. So out come the wheels and, similtaneously replacing the muffs, back in they go; hopefully this time more symetrically. This was a tricky process as the slidebars and crossheads are now in place and care is needed not to damage them.

Having undertaken this remedial work, I move onto the motion proper. You may recall that this is the work we are instructed to practice for. And it soon becomes obvious why. The links and arms are miniscule and making moving joints between them is a trial to say the least. This makes soldering coupling rod washers on seem a doddle.

The left hand side is the lubricating motion. At this point the instructions become quite dense and I found myself losing track and failing to understand how the whole was constructed. As well as rereading the instructions several times, I found reference to photographs in the RCTS book most useful and eventually felt confident enough to proceed. Manufacturing the two joints to assemble the three components was fairly straightforward; this work could be completed in the vice and cleaned up with relative ease.



Two close-ups of the motion in various positions. I'm not sure if the swing link should swing quite so much, but it doesn't seem to affect the running...


The assembly must then though be attached to the locomotive and necessitated holding the chassis in a cradle whilst the final joints were made. Attaching the swing link to the bracket on the chassis, the very last joint is the crank onto the the front wheel crank-pin. Being a layer of wheel > coupling rod > connecting rod > washer > crank, extra care was needed to avoid soldering the whole into a horrible mess. Once acheived, the whole lot was carefully cleaned up with files and abrasives and then washed to remove any stray flux.



A quick trundle up the test track reveals a working component; success albeit small in the scheme of things! Now for the other side...

Tuesday, 15 January 2008

Through the Wires

As promised, here are some pics of the N8 showing the chip installation.

i. General arrangement. The wires have been tweaked a bit more now, so that the front of the chip is higher.



ii. Front view showing the various bits of wiring. There is very little room either side of the motor and none on top where the rear spectacle plate actually touches the top of the motor. In comparison to find space for the wires, getting space for the chip was relatively easy.


iii. As such the wires are visible along the inside of the footplate; being orange doesn't help either! A touch of dark grey should render these much less obtrusive; the light grey one on the other side is less obvious even in its original state.


iv. The chip nestles nicely in the roof space and from all but the lowest viewpoints is invisible. A relative success and fairly quick and easy.


Sunday, 30 December 2007

Moving Pictures

Tired of the Bond film on ITV, or the latest episode of Eastenders. Try my alternative below. I can see that Peter Jackson shaking in his boots...

The Wheels in the Frames

I hope that you've all had a Merry Christmas! Done any modelling? Sneaked away from the turkey and the jollities for a few hours? Well I managed to do a bit more on the D49 between the pudding and the Port. Fortunately before the Port!

Having fabricated the various bits of motion, I proceed to fit the gears and driving wheels. First, though, I remove the frame extensions; carefully parting them from the frames proper with my piercing saw. The ends are cleaned up with a fine file. Additionally the frames need to be coloured. For the first time on a locomotive, I thought I would use Gun Blue rather than painting. This has the advantage of giving good coverage without the thickness built up with paint. Both methods seem to rub slightly with use, but a light oil of the blueing seems to prevent this somewhat.


The fitting of the wheels was fairly straightforward and the drivers were soon in place and quartered; the coupling rods held in place with fine wire insulation. I then come to the motion; crossheads, slidebars and connecting rods.


The slidebar slots into square holes in the cylinder face and a small pip at its rear lines up with the hanger, further back on the frame, when it is sufficiently inserted. Some fettling of the slidebar is required to get it far enough in. I have not soldered the slidebar to the cylinder, but merely tacked it to the hanger, being careful not to solder the crosshead at the same time!


Similtaneously, the crosshead rod has been slid into the tubing in the cylinder and of course requires no soldering whatsoever.


One at a time, the connecting rods are placed over the front wheel's crankpin and smooth running is sought. This took a little time and some further fettling of the slidebars was necessary as they had a tendancy to distort slightly during fitting. The second set required a little more attention than the first, but eventually all is in place and running smooth.

Thursday, 20 December 2007

Cruel and Unusual

Now the next part of the instructions suggest you practice before proceeding. And quite right too. Following on from the Crosshead/Slidebar saga we are now going to make the various bits of motion. To be fair, the D49/2 is the easiest option as the valvegear is just .3mm wire and the various linkages and rocking bits are missed out. However I still need to solder some joints; initially the crosshead to the connecting rods.

The connecting rods are a simple double-up and sweat together etch. I was careful not to get solder near the rod ends as these subsequently need to be free on a joint soldered to another piece.

A piece of .3mm wire is held in the vice and the components are slotted on. The instructions suggest a piece of oiled paper (fag paper) is inserted between the back of the crosshead (which is where solder will be applied) and the connecting rod (where it shouldn't!). It proved beyond me to thread the said piece of paper over the wire; bear in mind that the crosshead is already on the wire by virtue of the hole at the back (out of sight). So I cut a slot in a piece, oiled it, and then slid it into place. Worked a treat!

Before getting too keen with the soldering iron, check the connecting rod will move freely in the unsoldered joint. There is next to no space in this tiny joint and I had to file the outer circumference of the con rod hole to get clearance.

After soldering, the assembly can be removed from the vice and the wire trimmed. I think the instructions indicate that the crosshead should be in the slidebars by now. However, I found the two easy to assemble and disassemble even in their bent-up state. Doing this joint with the slidebar flapping around too would have been a nightmare.

One down, one to go. We might have wheels on before New Year at this rate!

Thursday, 6 December 2007

Close To The Edge

Well, we're really starting to chart unknown territory now.


The next step is to fabricate and insert the "Piston" tubes into the cylinder block. This is fairly straightforward; carefully shortening the tube in the mini-drill and regularly checking length. Then soldering into the cylinder block flush with the front and protruding somewhat at the back. I used my small soldering iron (an Antex 12W) for the first time in quite a while. I've got used to using the 18W; the extra power more than compensates for the bigger tip. But here there isn't the space and the 12W works just fine.




Slidebars come in three pieces and the instructions say to tack solder them at the front only. I presume this is to avoid solder in the slide slot which may impede the smooth flow of the Crosshead. The Slidebar is at the bottom of the picture:








The scary bits are at the top of the picture; the Crossheads. Now I know the instructions say to read the instructions etc. etc... But by the time I've got to page 6, I've forgotten most of page 5, and so on... So despite the instructions, I removed the pieces from the etch. Mainly because they seemed to be flopping around when I'd removed some other pieces, not out of any perversity you understand. Some very flimsy rings have to be reamed out to slide over the 0.7mm rod and then folded over on half etched hinges to make three layers. I managed to break two lots of hinges whilst reaming, but subsequently the whole lot did get soldered onto the rod.



Having done this, another piece has to be soldered on square and with the minimum of solder so as not to obscure some tiny holes. Here I failed; the pieces are square, but the holes are full of solder! Nevermind; I shall drill them out. Anyway the Crossheads do slide nicely in the Slidebars. The instructions tell me not to fit all this to the chassis yet as there is more work to be done. Oh crikey!!

Seriously though, this is some of the hardest fabrication I have had to do. It has required constant concentration and effort, but the results are more than worth it. Bear in mind the whole assembly is smaller than your thumbnail (unless you have particularly dainty hands).

The Crosshead sticking through the cylinder block. Not as painful as it sounds.

The Crosshead in the Slidebar; all slippy and super smooth. Don't sneeze though...

The other thing to mention is that this will be my first DCC loco; I've decided to take the plunge! Fingers crossed!!!!

Wednesday, 28 November 2007

Lets Get Metaphysical

Have you noticed how some of the things we do whilst modelling have a quality which transcends the actual modelling? For example, to me, the act of cutting good quality cardboard with a brand-new scalpel brings a certain pleasure that bears no relation to what is actually being modelled. I could, in theory, be most content just cutting small squares of cardboard all day. In reality, of course, the end product has importance, but think next time you sit down to do some modelling, "What am I getting out of this?" It might help prioritise the kind of modelling you should be doing.

Another activity which pulls the strings for me is using the Piercing Saw. Now I haven't had this bit of kit out of late, but progress on the D49 means that I am now in a position to remove the metal components which currently straddle the chassis sideframes. Gently pulling the blade over the metal etches and feeling the cut, almost as easy as a knife through butter, is satisfaction made physical.



So the D49 moves slowly forward. The spacers were fabricated and drilled and gapped. On the whole their placing was relatively straightforward. The instruction warn that one of the drive gears is close to a spacer and care is needed. In reality I found that the space allowed was fairly generous and ought not to cause a problem. A couple of spacers had to be soldered down between the frames flush with some half-etched lines (to subsequently mount the brake-gear). I found this quite tricky and a couple of tabs in the frames to aid location might have been a good idea. Anyway I persevered and they're in the right place now. I hope!